Home > Hard Drive > HDD In Secondary IDE?

HDD In Secondary IDE?

Contents

The master device is connected in the middle of the cable, and the slave at the end of the cable. A diagram of the pins you need to place the jumper over to select a certain configuration should be displayed on the hard drive label or in the manufacturer's documentation. Put your older drive on the Secondary channel with your CDROM as the Master. Assign the drive letter.

The Master drive goes on the black connector at the end of the cable, the slave drive connects to the gray connector in the middle and the host adapter connects to There is a connector at each end of the cable and another one about two-thirds of the distance from the motherboard connector. solved what is the difference between primary and logical drives? Discussion topics include SSD, SATA drives, USB drives, external hard drives, RAID arrays, backup, IDE drives, network attached storage (NAS), thumbdrives, Western Digital, Kingston, LaCie, and SanDisk.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General http://www.makeuseof.com/tag/install-ide-hard-drive/

Ide Hard Drive Jumper Settings

Locate a free one from the power supply and plug it into the connector on the drive. Although the Cable Select specification may simplify things in the future, there will probably be lots of confusion, especially on legacy systems, as this starts to be introduced. Depending upon your bios and startup options, if it is like mine you have the option either within the bios, or at startup, which drive to choose as the primary. The ATA-1 specification was released in 1994, and was withdrawn in 1999.

The secondary IDE channel runs the CD-RW / DVD combo drive. Serial ATA is not compatible with the IDE [Parallel ATA] because the connectors are different, the voltage levels are different, and data format is different [SATA sends a bit at a Some controllers lock the whole channel, a few do not. Seagate Ide Hard Drive Jumper Settings Go into the Control Panel -> go under Administrative Tools -> Computer Management -> Storage -> Disk Management.

Static discharge can jump and do some bad things. How To Connect Ide Hard Drive To Sata Motherboard Setting the jumpers What are jumpers? So does this also mean that if I have 2 optical drives on my secondary controller that my newer DVD-RW would be slowed down by my older DVD player? http://www.tomshardware.com/forum/158321-45-difference-primary-secondary-channels This is > a new burner and capable of UDMA 4.

Format the drive. Western Digital Ide Hard Drive Jumper Settings Close up the case and boot directly into BIOS Setup.Check on one of the first pages for an IDE device. For the location of the jumper selector see the diagram on the left. Do I need to set the pin in a different location cause the master is a Sata???

How To Connect Ide Hard Drive To Sata Motherboard

Proffitt Forum moderator / December 7, 2006 5:45 AM PST In reply to: SATA & IDE Combination Troubles--but w/ SATA adapters IDE's But I'll decline why since this post is buried http://www.easeus.com/resource/install-ide-hard-drive.htm Anmelden 24 Wird geladen... Ide Hard Drive Jumper Settings Categories 45958 All Categories6603 Gaming 16747 Hardware 19274 Science & Tech 1856 Internet & Media 851 Lifestyle 28053 Community Hard drive on secondary IDE? How To Connect Ide Hard Drive To Motherboard by R.

Reply Adam August 24, 2016 at 3:50 pm Did you have to reformat the HDD to run as a slave on the newer box? Wird geladen... There is a reason for this. The older Master & Slave relationship For the longest time, hard drives have always had a setting for a Master or Primary setting and Slave. How To Install Ide Hard Drive

Someone correct me if I'm wrong. 0 ryko new york Feb 2006 edited Feb 2006 roland_dmp, your reasoning seems logical, but i do believe you are incorrect. If you are adding a second drive then try and leave a gap between the two drives for ventilation, although this might not always be possible. If this is being installed as a secondary storage drive for Windows, then you can go into the built in utility called "Disk Management". Carefully but firmly plug the IDE and power cables in and then move onto finishing the installation below.

Why does my motherboard detect my ATA100 hard drive as a ATA33 or DMA mode 2? Ide Cable Select Removing an old SATA hard drive The data cable of a SATA hard drive is slightly easier to remove than their IDE counterpart, however it is better to unplug both cables Jumpers are small black plastic sleeves that slide over the top of metal pins.

If you're opening up something an OEM machine you could be voiding your warranty so check first.

As long as your motherboard has both SATA and IDE connections available and you set the switches on the drive appropriately, it should work! Note: If you want to recover data from the "OLD" drive, don't do this! When you try to install a really big hard drive into a lot of older systems, you'll find that the BIOS is only capable of seeing 137 GB. How Many Hard Drives Can Be Connected To A Single Ide Cable Flag Permalink This was helpful (0) Collapse - Ahh, that never seems to work.

Using PIO Modes 0, 1, 2, 3, or 4 and Multiword DMA modes 1 and 2 and Ultra DMA modes 0, 1, and 2. EaseUS softwar… Related Products Data Recovery Software Data Backup Software Partition Manager Software PC Transfer Software Mac System Utility File Sync Utility Top 10 Hot Articles Recover Pictures after Factory Reset I can boot off of the SATA drive regardless, but the OS (WinXP Pro) will not see the IDE drive. The normal PC cables have three connectors, one for the mother board (at one end) and two for device attachment.

You can attach up to two units on the cable, one master and one slave. Now you should be able to find an open 3.5" slot somewhere. I'm using 3 maxtor HD's 80 & 120 gb sata + 200 gb pata, and 3 dvd burners BENQ 1625, & 1610, + LG GSA 4163B. Flag Permalink This was helpful (1) Collapse - It's about reading mobo doc and following instructions by Doug_Hirschfeld / July 28, 2005 11:10 AM PDT In reply to: It's all about

Volume label is nothing other than the name you want it to be called. Sata is primary drive and it was automatically set to drive H. If the drive is to be the slave then use the slave connector.