Home > Hard Drive > HDD And CD On Same IDE Port

HDD And CD On Same IDE Port

Contents

All Rights Reserved. As of May 1, an ISP/EDU email is NO longer required to access the Classifieds. If using the standard 40-wire cable, the Master goes in the middle connector and the Slave goes in the end connector. Acción en curso...

This is where almost all headaches and problems came in. Powered by vBulletin Version 4.2.2 Copyright © 2017 vBulletin Solutions, Inc. In fact, there is no pin at that position. Write out a quick table to figure out how it is currently set up, like this: CHANNEL 1, MASTER: CHANNEL 1, SLAVE: CHANNEL 2, MASTER: CHANNEL 2, SLAVE: Probably your hard http://www.tomshardware.com/forum/261305-32-hard-drive-cable-drive

Ide Hard Drive Jumper Settings

They look this this 99% of the time: [ The smaller one on the very top is a floppy drive controller connection ] There is a Primary & Secondary connection located Publicado el 29 may. 2013Easy HDD In Master//DVD Drive In Slave// Thatz All Jumper Pin Setting will differ with different Companies So Read the Image Above the HDD Its Easy!!!!!!!!! The cd drive ones are capable of much slower copy rates.

Book your tickets now and visit Synology. Only some of the latest optical drives that burned DVDs at 16x or higher started to use ATA 66 and required a 80 wire cable to work at high speeds. Another design would have the host interface connector in the middle and the two drives would plug into each end of the cable, with the connector at one of the ends Sata Power Cable Multiple Connectors One problem will be in selecting the correct cable.

Cargando... How Many Hard Drives Can Be Connected To A Single Ide Cable Reply With Quote 02-27-04,03:04 PM #5 stool View Profile View Forum Posts Senior Member Join Date Dec 2000 Location Albany, NY There is no reason in the world not to, Computer Services Tel 650.548.1010 Burlingame, CA USA Connecting IDE Hard Drives You Would Think It Was Simple, But... http://www.overclockers.com/forums/showthread.php/275292-Hard-drive-and-CD-ROM-on-the-same-IDE-cable Deshacer Cerrar Este vídeo no está disponible.

If only one drive needs to read/write data (like most of the time) then the performance is the same. How To Connect Dvd Drive To Motherboard Sata Set The Jumpers & Plug In Since I only have a single IDE CD-ROM and single hard disk to show you today (as well as only a single physical IDE connector We also taught you all about partitions How To Set Up A Second Hard Drive In Windows: Partitioning How To Set Up A Second Hard Drive In Windows: Partitioning Read More Like PATA, the SATA specs have evolved quickly to improve data transfer.

How Many Hard Drives Can Be Connected To A Single Ide Cable

The time now is 08:40 AM. http://www.makeuseof.com/tag/install-ide-hard-drive/ Advertisement On the motherboard end, the socket looks like this. Ide Hard Drive Jumper Settings So if you had an ATA33 CD drive with an ATA66 hard drive, the BIOS would force the hard drive to talk at ATA33. What Is The Voltage Of The Red And Yellow Wires On Most Power Supplies? Añadir a ¿Quieres volver a verlo más tarde?

OSNews and the OSNews logo are trademarks of OSNews. The hard drive that I'm using is for storage. Copyright ©2000 - 2014, iNET Interactive Overclockers.com Register New Posts Advertising Contact Us Archive Sitemap Top iNET Interactive Copyright © 2014 iNET Interactive. There are several "standards" of communication between devices and the motherboard through the IDE cable: PIO 4, ATA 33, ATA 66, ATA 100, ATA 133. How To Connect Two Sata Hard Disk In One Pc

The older 40-wire and the newer 80 wire are both 40-pins! Home Forum New Posts FAQ Calendar Community Groups Albums Member List Forum Rules & Guidelines Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Reviews News Read your doc to see how your board works. Shortly that IDE drive will host several versions of Linux as I turn the computer into a dual boot machine.

if it is not then i would say make it the slave it will interfer less with the transfer rate if it is the slave. Ide To Sata Converter Cambiar a otro idioma: Català | Euskara | Galego | Ver todo Learn more You're viewing YouTube in Spanish (Spain). You can attach up to two units on the cable, one master and one slave.

TechSkillsVideos 216.251 visualizaciones 9:41 How to connect SATA devices in a PATA (IDE) only PC system - Duración: 2:33.

Reply With Quote 02-29-04,01:40 AM #14 JigPu View Profile View Forum Posts Inactive Pokmon Moderator Join Date Jun 2001 Location Vancouver, WA Anybody who tells you that it's "not reccomended" Iniciar sesión 5 Cargando... The difficult part is the jumper settings, which will vary according to your device. Pata Hard Drive When connecting IDE devices in your computer, there are a few rules you need to know about.

Drive dongles like the Syba do not require device drivers. You set a switch on back of this connector to indicate whether you are going from IDE to SATA, or from SATA to IDE. This is normally where you connect your lesser used devices like CDROMs, CDROM Burners and Tape Drives. It's that way for a reason.

Required fields are marked *Comment Name * Email * James Bruce 631 articles James lives in the middle of nowhere with his wife, son, and chickens. Gosh, it's been awhile since I've thought about that stuff!! If the CD-ROM is far from the hard drives, you will need one cable for the hard drives, and another going to the CD-ROM. But if you have two things on the same IDE cable, then they can't both read/write at the same time.

It really didn't matter much until the hard drive makers started making drives with the Cable Select option. Any other advice? Can I put my brand new CDROM Burner on the Slave position on my 80-wire cable? The other drive or Slave drive was for data storage.

Would I be able to connect it on the same IDE cable as the CD-ROM? I'll answer these questions from a practical standpoint for those working with consumer desktops. How can I connect a SATA drive to an old motherboard having only IDE sockets? G sunnystaines 14:07 20 Dec 09 make sure hdd is primary Ballie 14:22 20 Dec 09 Sunnystaines,the hdd on the IDE cable will only be a back up/storage drive

The red SATA data cable is plugged to connect to a SATA motherboard socket to support data transfer. My Computer > (right click) > Manage > Disk Management Shows No Drive (I:) or (J:), i.e., nothing in IDE Port 2. The Drives & Jumper Settings Whether it’s a CD-ROM drive or hard disk, IDE drives are identical in terms of connectors.